T-1/DS-1 Access

These are highly-regulated services traditionally intended for businesses, that are managed through Public Service Commissions (PSCs) in each state, must be fully defined in PSC tariff documents, and have management rules dating back to the early 1980s which still refer to teletypes as potential connection devices. As such, T-1 services have very strict and rigid service requirements which drive up the provider’s maintenance costs and may require them to have a technician on standby 24 hours a day to repair the line if it malfunctions. (In comparison, ISDN and DSL are not regulated by the PSCs at all.)

Due to the expensive and regulated nature of T-1 lines, they are normally installed under the provisions of a written agreement, the contract term being typically one to three years. However, there are usually few restrictions to an end-user’s use of a T-1, uptime and bandwidth speed may be guaranteed, quality of service may be supported, and blocks of static IP addresses are commonly included.

Since a T-1 was originally conceived for voice transmission, and voice T-1’s are still widely used in businesses, it can be confusing to the uninitiated subscriber. It is often best to refer to the type of T-1 being considered, using the appropriate “data” or “voice” prefix to differentiate between the two. A voice T-1 would terminate at a phone company’s central office (CO) for connection to the PSTN; a data T-1 terminates at a point of presence (POP) or datacenter. The T-1 line which is between a customer’s premises and the POP or CO is called the local loop. The owner of the local loop need not be the owner of the network at the POP where your T-1 connects to the Internet, and so a T-1 subscriber may have contracts with these two organizations separately.

The nomenclature for a T-1 varies widely, cited in some circles a DS-1, a T1.5, a T1, or a DS1. Some of these try to distinguish amongst the different aspects of the line, considering the data standard a DS-1, and the physical structure of the trunk line a T-1 or T-1.5. They are also called leased lines, but that terminology is usually for data speeds under 1.5 Mbit/s. At times, a T-1 can be included in the term “leased line” or excluded from it. Whatever it is called, it is inherently related to other high-speed access methods, which include T-3, SONET OC-3, and other T-carrier and Optical Carriers. Additionally, a T-1 might be aggregated with more than one T-1, producing an nxT-1, such as 4xT-1 which has exactly 4 times the bandwidth of a T-1.

When a T-1 is installed, there are a number of choices to be made: in the carrier chosen, the location of the demarc, the type of channel service unit (CSU) or data service unit (DSU) used, the WAN IP router used, the types of speeds chosen, etc. Specialized WAN routers are used with T-1 lines that route Internet or VPN data onto the T-1 line from the subscriber’s packet-based (TCP/IP) network using customer premises equipment (CPE). The CPE typical consists of a CSU/DSU that converts the DS-1 data stream of the T-1 to a TCP/IP packet data stream for use in the customer’s Ethernet LAN. It is noteworthy that many T-1 providers optionally maintain and/or sell the CPE as part of the service contract, which can affect the demarcation point and the ownership of the router, CSU, or DSU.Although a T-1 has a maximum of 1.544 Mbit/s, a fractional T-1 might be offered which only uses an integer multiple of 128 kbit/s for bandwidth. In this manner, a customer might only purchase 1/12th or 1/3 of a T-1, which would be 128 kbit/s and 512 kbit/s, respectively.T-1 and fractional T-1 data lines are symmetric, meaning that their upload and download speeds are the same.

This article is licensed under the GNU Free Documentation License. It uses material from the Wikipedia article “Internet access”.